2000M Remote Controllers for 2 Different Sirens

Question from Customer:
Hello, I would like some help to decide on what system to choose. We have a siren in a building 750m away that we would like to trigger, it is 240v. I would also like to use the same remote to activate a 12v siren 1.2km away. Is it possible for one remote to trigger two different sirens?
Answer:
We recommend you two different receivers, one is long range ac power direct output receiver (S1X-AC220-ANT2), and other is long range dc power direct output receiver (S1X-DC12-ANT2). AC receiver is used to connect to 240V siren. DC receiver is used to connect to 12V siren. You can only use 2-Button transmitter (CB-2) to control all of them. With the extended external antenna, both receivers’ working distances reach 2000m (6000ft).
remote control kit
Usage:
There are three working modes in each receiver.
1) Setting control mode Toggle: Only connect Jumper-2.
Press button 1: Turn on the relay.
Press button 1 again: Turn off the relay.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold button 1: Turn on the relay.
Release button 1: Turn off the relay.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press button 1: Turn on the relay.
Press button 2: Turn off the relay.
In your case, you can set ‘Toggle Mode’. Press the button of remote, turn on the device; press the button again, turn off the device. Toggle mode is motivated by single relay, which means you can work this mode with single button remote. So one 2-Button transmitter is enough for you to control two sirens. Press big button, turn on the 240V siren; press again, turn off the 240V siren. Press small button, switch on the 12V siren; press again, switch off the 12V siren.
Wiring:
240V siren is connected to AC receiver’s OUTPUT terminal. And supply 240V power supply. 12V siren is supposed to connect to DC receiver’s A&B terminal. And supply 12V power supply.
circuit

Comments

Post a Comment

Popular posts from this blog

What is Toggle / Momentary / Latched Modes

Generally there are three working modes for rf remote controls : toggle, momentary, latched. Toggle mode is used most often. Controlling lamp, for example, press the button of remote, turn on the lamp; press the button again, turn off the lamp. Momentary mode can be set to control rolling blind or rolling door. You need to press and hold the button of remote to make the blind or door open/close. Both toggle and momentary mode are motivated by single relay, which means you can work these two modes with single button remote. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time, e.g. press remote button A, relay A will be on, and relay B will be off; press remote button B, relay B will be on, and relay A will be off. To be more specific, when you control the lamp by latched mode, you should prepare at least two buttons remote. Press button A, the lamp is on; press button B, the lamp is off. Information from: http://
Read more

Difference between traditional two-way switch and new electrical touch two-way switch

Image
Various electrical touch two-way light switch from  https://www.remote-control-switch.com Generally speaking, two-way switch controls one light from two locations: for example, the long hallway could have a switch at each end to control one hall light. Or a large family room that has two entrances could have a switch at both entrances to operate one overhead light. A two-way switch allows you to turn on the light conveniently when you enter an area rather than stumble through the dark to find the switch. Now we are going to talk about the difference between traditional two-way light switch and new electrical touch two-way switch. First of all, let’s see what are traditional two-way switch and new touch two-way switch. Traditional two-way switch has a single pole double throw configuration (SPDT). Each has a common terminal (COM) with a pole that can be switched between position L1 or L2. As diagram below shows, the live wire is connected to Switch1, and flow to the lamp through L1
Read more