Home Automation Control

Question from customer: I want a kit radio module 1 channel (12V), can transmit the state of a dry contact input (on transmitter). This is to retrieve the status of a motion detector. Distance 60m open field. Answer: We recommend 1 channel 12V rf receiver and transmitter with dry contactinput (S1L-DC12-ANT2 & CB-2N ). The very special design is its transmitter with a dry contact input aside. The triggering method of this transmitter is connection of two wires on it. There is only one channel at that relay on the receiver. The output contacts of relay are normally open and closed. Working distance of transmitter and receiver with external extend antenna are 2000M / 6000ft (theoretically).     Wiring: Wires on the transmitter should be connected to the contacts of motion detector (original device). The normally open contacts B&C of receiver should be connected to the device being controlled. Maybe you can wire a lamp to the re...

Question from Customer: “I am looking for a remote controller to start and stop a motor of 1/2 horsepower from a distance of 250 – 300 feet. The motor is 115 volts AC. Which unit is correct for this application?” Answer: We recommend 1 channel AC 30amps 2000m Remote Cont roller (S1PX-AC220-ANT2 & CB-2) to you. There are 3 working modes in this kit. They are toggle, momentary and lathed mode. You can choose momentary or latched mode. Momentary Mode : Only connect Jumper-1. Press and hold big button: Turn on the relay, terminal OUT outputs AC power, motor starts. Release big button: Turn off the relay, terminal OUT no output, motor stops. Latched Mode : Do not connect Jumper-1 and Jumper-2. Press big button: Turn on the relay, terminal OUT outputs AC power, motor starts . Press small button: Turn off the relay, terminal OUT no output, motor stops. The controller’s transmitting distance can be about 2000m in the open field. With its high amp load-30amp, it is enough stron...

Question from customer: I want to install a single channel remote to control my doorbell within the range of 150m. The old 6V doorbell was broken and I don’t want to repair the wires of doorbell. Ordinary wireless doorbell cannot be used because it doesn’t reach the distance I really want. I have an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 150m. Would you like to recommend some favorable products? Answer : We recommend the 6V one channel 2000m receiver (S1U-DC06-ANT2) and long range transmitter (CB-1). Working voltage range of receiver is 6V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 6V doorbell. Usually, you don’t have to supply additional power to doorbell because it can get 6V power from powered receiver when you connect them to the 6V power supply together....

Question from customer: I would like some help to make my Horn starting system become remote controlled. At present I have a momentary switch on a 12 foot cable when the switch is press it activates the horn. I would like the horn and housing to be separated. I would like the horn to be approximately 100M away. Which of your products will help me? In the future I would like to add a 2nd and 3rd horn to my set up which will be housed in separate boxes. Answer: If you want to remote control a horn, we recommend the long range 1 channel 12V momentary receiver (S1XM-DC12-ANT2) and the long range transmitter CB-1. It is direct power output; control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. Its working distance can reach 2000m with external extended antenna. ...

Question from customer: When the tank is empty my float switch makes contact and stays in this mode till the tank is full. What I need is for the transmitter to activate the receiver and hold it in the on position till the float switch interrupts the transmitter and releases the receiver. I need a receiver which is only activated as long as the transmitter sends a signal. Or I need a way to make the transmitter send a signal when the float switch makes contact, then interrupts this signal and sends a second signal when the float switch interrupts contact. Answer: We recommend the model of normally open latched 2000m remote controller (S1L-DC12-ANT2 & CB-2N). The receiver is with magnetic antenna and only one working mode—latched mode. It is activated the 12V power. The transmitter is designed with novelty. There are two wires extending from transmitter. The triggering method is connection and disconnection of two wires. When two wires are connected, “ON” signal will be sent ...

Question from customer: I want to install a set of wireless remote controls, include 8 transmitters in 8 different places (max. 500 m) and one receiver in a specific location. The transmitter transmits a wireless signal to control a closed contact. Answer: We recommend normally open/closed contact toggle remote control (S1T-DC12-ANT2+CB-1). According to your requirement, you can choose 8 transmitters (CB-1) to work with the receiver. There are normally open/closed contacts in it which are able to connect device activated by DC 0~28V or AC110~240V. With external extended antenna, its working distance has reached 2000M in the open field. You can use 8 transmitters to remote control receiver from different directions. This kind of remote control is activated by DC12 power supply. Toggle Mode is the only working mode of it. Here is the wiring diagram. Initial state: A, B = Normally Closed; B, C = Normally Open. Wire your device to normally closed contact A&B terminals. If you do t...

This is the 4 channel multi-mode dc RF remote control kit. Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. There are 4 working modes for your requirement. With the external extend antenna, its working distance can reach 2000m(6000ft) in open field. Operation Video:

Question from Customer: Hello, I would like some help to decide on what system to choose. We have a siren in a building 750m away that we would like to trigger, it is 240v. I would also like to use the same remote to activate a 12v siren 1.2km away. Is it possible for one remote to trigger two different sirens? Answe r: We recommend you two different receivers, one is long range ac power direct output receiver (S1X-AC220-ANT2), and other is long range dc power direct output receiver (S1X-DC12-ANT2). AC receiver is used to connect to 240V siren. DC receiver is used to connect to 12V siren. You can only use 2-Button transmitter (CB-2) to control all of them. With the extended external antenna, both receivers’ working distances reach 2000m (6000ft). Usage : There are three working modes in each receiver. 1) Setting control mode Toggle: Only connect Jumper-2. Press button 1: Turn on the relay. Press button 1 again: Turn off the relay. 2) Setting control mode Momentary: Only conne...

100M RC Fireworks Ignitor 2000M Long Range RC Fireworks Ignitor This rf wireless remote control ignitor can light various kinds of electric fireworks directly, or ordinary fireworks through ignition head, which reduce accidents like skin burn and accidental explosions. One ignitor can light several fireworks at the same time. One transmitter can control many ignitors simultaneously. The ignitor can be remotely controlled from any place within 100m; wireless signal pass through walls, floors and doors. More information please visit  http://www.rfcontrolsystem.com