Perfect White Glass Panel Remote Touch Two-Way Switch

General Description:

This remote touch two-way switch can control two sets of lights by working with another same two-way light switch. It can be touch or remote controlled. With the mini remote control, the user is able to control lights in different rooms, without the need for going around to turn on/off the lights by hand. Its perfect white crystal glass panel creates an exclusive ambiance to any room or setting.

Specific Parameters:

Dimension: 86mm*86mm*37mm
Material: Crystal Glass Panel
Operating Voltage: AC110V~250V/50Hz/60Hz
Maximum Current for Each Gang: 5A
Minimum Load Power for Each Gang: 15W
Maximum Load Power for Each Gang: 1000W/220V or 600W/120V
Self Consuming Power: Less than 0.1mW
Operating Environment: -30~70 Centigrade; Less than 95%RH
Lifelong: 100,000 Times of Operation
Using with all types of lights including Incandescent lamps, Halogen lamps, Fluorescent lamps, Energy saving lamps.
Note: The switch is not suitable for LED lamps or inductive ballast fluorescent, or any lamps with load power lower than 15W.

Switch Operation:

Power on the switch, it will enter into initial status. About 10 seconds later, you can operate the switch.
The two way switch only works after matching each other.
Matching steps:Touch slightly the icon on the switch connected with lamp for 5 seconds; take away your finger when you hear the sound of “Di”. Then touch any icon on the other switch, the lamp turns on/off, which means the success of matching.
Matching cancel steps:Touch any icon of switch connected with lamp for 10 seconds until hearing two sounds of “Di”, and then takes away your finger immediately. All the matching will be cancelled.
Operation:Touch softly the icon on any one switch surface, the LED indicator turns red, which means turning on the light.
Touch again the icon on any one switch surface, the lamp turns off.

Note:
Please don’t take away your finger when you hear one “Di” sound.
The quantity of connected two way switch cannot exceed three.
The total load power can’t exceed 1000W for all connected two way switches.
The distance between two sides of A/B can’t exceed 30m.
If the switch is not connected with any lamp, there is no sound when matching. Remote function is not available.
Not support remote scene mode.

Remote Control Specification:
Size: 61mm x 33mm x 12mm
Buttons: 4 keys (A, B, C, D)
Control Lamps: 3 pcs
Remote Distance: 20m
Current: 15mA
Frequency: 433.92 MHz
Battery: 1 x 27A/12V battery (included, can be used for 12 months)
Press key A, key B, key C, the corresponding lamp will be ON; press key D, all lamps will be OFF.

Remote Control Operation:
Register the remote: Press the effective touch zone of switch for 5 seconds; you will hear the sound of “Du”. Then press key A, key B or key C. You will register successfully after you hear the sound of “Du”.
Cancel one registered remote: Press the effective touch zone of switch for 5 seconds; you will hear the sound of “Du”. Then press key A, key B or key C. If this operation is successful, you can hear two continuum sounds of “Du”.
Cancel all registered remotes: Press the touch zone of switch for 10 seconds. You can hear the first sound of “Du” when it is in 5 seconds; and you can hear the second sound of “Du” when it is in 10 seconds, which means this operation is successful.

Note:
Press key D, all lamps will be off.
Each switch are capable of registering 8 remote control buttons, the first one will be canceled when you register the ninth one.
Two switches cannot be registered at the same time.
Seconds’ interval is required for two times of remote control operation; otherwise the operation will be ignored.

Installation:
1. Shut off the power to the circuit and remove the switch cover with screwdriver.

2. Connect the wires to the switch’s screw terminals.

Note:When one two way switch connects with another, any one switch connected with live wire is enough.
Lamp like L1/L2/L3 can connect with any one of two switches.
Both communication line A & B from one switch should be connected with others. Communication line A from one switch is forbidden to connect B from others, only A to A, B to B.

3. Fix tightly the switch to internal box with two screws.

4. Fix the cover.