Home Automation Control

Question from customer: I need a 2 channel receiver with 2 remotes 1 channel. One remote control activates the channel A receiver on the receiver and another remote to turn on the channel B on the receiver. Is it possible with the CWB-1 model? And which receiver would like to recommend? Answer: We recommend 2 channel12V multi-mode receiver (S2U-DC12) and two waterproofwireless 50m remotes (CWB-1). We set configured code for them so that they can work together. The receiver is 12V activated and has two relays. When it works with that transmitter, its transmission distance can reach 50m in the open air. There is only one button on each transmitter. It can control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors, doors...

Question from customer: I want a kit radio module 1 channel (12V), can transmit the state of a dry contact input (on transmitter). This is to retrieve the status of a motion detector. Distance 60m open field. Answer: We recommend 1 channel 12V rf receiver and transmitter with dry contactinput (S1L-DC12-ANT2 & CB-2N ). The very special design is its transmitter with a dry contact input aside. The triggering method of this transmitter is connection of two wires on it. There is only one channel at that relay on the receiver. The output contacts of relay are normally open and closed. Working distance of transmitter and receiver with external extend antenna are 2000M / 6000ft (theoretically).     Wiring: Wires on the transmitter should be connected to the contacts of motion detector (original device). The normally open contacts B&C of receiver should be connected to the device being controlled. Maybe you can wire a lamp to the re...

We recommend this kind of remote controller- dc rf remote controller kit with timer (S1D-DC12 & C-1), which operates in the 315/433 MHz frequency and is actuated by DC 6V, 9V, 12V and 24V. There is an adjustable resistor being installed in it. Working time of this remote controller can be adjustable between 2-40 seconds by using a screwdriver to twist the top of resistor. It can be applied to controlling lights, motors, fans, electrically operated doors/ locks/ windows/blinds/ cars or other appliances with voltage AC 110~240V or DC 0-28V. We’d like to show you the procedure of controlling dc led lamp.

Vibrating alerts are primarily used when a user (deaf people or aged people) cannot hear the ring tone (a noisy environment or through hearing difficulty) or want s a more discreet notification. Vibrating alerts is used in mobile phones. If you put vibrator to a hard surface, it will be louder than a ringtone. In fact, we integrate vibration and beep function into one item. So we’d like recommend this kind of 1000m rf tri-mode wireless vibrator kit (12Z-06 & CB-12). It includes 12 vibrators and a 12-button transmitter. This vibrator kit’s transmission distance is about 1000m. There are four working modes in them. They are vibration, beep, vibration and beep. Here is the usage of vibrator kit. The first step is learning. 1) Press and hold the learning button of the receiver(vibrator) for about 5 seconds, then release the button when LED light is on, the receiver (vibrator)is in the status of Learning. 2) Press button of remote control within 10 seconds, if LED light flashes t...

Question from customer: “I have a waterfall water feature that currently has an 110v 250W pump that run from 7AM until 10PM. I would like to save more energy by having these pumps turn on by detecting motion near the water feature. 110 degree detection, within 30 feet would be sufficient. The more intelligent, the better (i.e. body/heat/motion/mass detection). There is no need to run a waterfall water feature when no one is there to enjoy it. What do you recommend?” Answer: We recommend wireless infrared movement detector and receiver with time delay function (S1DA-AC220-ANT2&W-01) to you. This kit is 220V actuated. With external extended antenna, it can work within 6000ft in the open field. With adjustable time delay function, you can adjust delay time from 0 second to 99 hours. The motion detector can detect any movement within 10m. Detection range is fan-shaped angle 110°. We’d like show you how to use this kit. Steps: 1 Using screws to fix the bracket on the wall to fav...

This wireless calling system has 99-channel mode among working modes. In this mode, one receiver host can works with 99 calling transmitters. The receiver should pair up with three or four-button transmitter . We’d like to show you the procedure. We prepare a receiver host, 4-button calling transmitters, manager remote and 9V power supply for receiver host. There are three steps to pair up transmitters and receiver host. Working mode setting: After switching on power, press and hold button 1 of manager remote for 2sec to enter setting menu, press button “3″ or “4″ to choose Cd8, press button 1 again to enter submenu of Cd8, press button “3″ or “4″ to choose “5″ (Mode 5: 99-channel mode), press button “2″ to turn back to setting menu. Calling button pairing: Press button “3″ or “4″ to choose Cd7, press button 1 again to enter submenu of Cd7, press button “3″ or “4″ to choose “001″, Press any button of transmitter (except “Cancel”), the speaker will sound “successful registratio...